Motormaster
1September 25, 2017Sprues. Bottom left is de-chromed.
2September 25, 2017Who thought this was a good idea of attaching parts?
3September 25, 2017This kit is a bit older....
4September 25, 2017Like Kerry Cox says, remove the lines
5September 28, 2017Sand away!
6September 28, 2017This cannister is a bit too close to the holder.
7September 28, 2017Much better. Needs to be sanded a bit more.
8October 5, 2017Who thought this is a good idea of connecting the sprue to the part?
9October 5, 2017Luckily no damage done.
10October 5, 2017Mind the gap.
11October 5, 2017Mind the gap. This being an older snap tite kit, dry fitting is hard/tough/impossible.
12October 5, 2017After a lot of sanding, filling and more sanding....
13October 5, 2017These tanks seem acceptable.
14October 15, 2017Right original, left drilled. Better!
15October 15, 2017Just these two stacks took nearly 45 minutes to erase the seamlines.
16October 21, 2017Some more to sand.
17October 21, 2017Done
18October 21, 2017Only light sand work needed
19October 21, 2017Fill the gap!
20October 21, 2017And sand
21October 21, 2017Drive shaft needed some attention
22October 21, 2017One of the antennae on the mirrors was broken.
23October 21, 2017Replaced them with 0.5mm rod
24October 21, 2017Only soft sanding along the edges.
25October 21, 2017This small piece neede a lot of sanding. Put it in the drill handle for extra grip.
26October 21, 2017Finished
27October 21, 2017
28October 21, 2017Flash & seamlines...
29October 21, 2017Way better
30October 21, 2017Tiny stuff
31October 21, 2017The sides of the handles needed only scraping
32October 21, 2017tired of sanding red pieces, turned attention to black pieces. Same here 🙁
33October 21, 2017After sanding & smoothing
34October 22, 2017These tires will be impossible to get right without rescribing. Which I won't be doing.
35October 22, 2017Left original, right treated.
36October 22, 2017Almost forgot a red part.... This one actually is pretty clean. Just some very light sanding.
37October 22, 2017And some ugly marks here and there.
38October 22, 2017Cleaned up.
39October 22, 2017Degreased and drying. Time for priming!
40October 23, 2017First batch primed Alclad High Gloss Black. Started with the interior and noted I accidentally had loaded Alclad matt black microfiller. Luckilly I didn’t start with the cab.
41October 25, 2017Test piece. To the right Alclad 107 Chrome over Alclad’s black microfiller primer. To the left same Chrome over Alclads High Gloss black primer. Spot the difference 😉
42October 28, 2017Quite happy with the result
43October 28, 2017Lower parts of the stacks painted silver
44October 28, 2017Some details painted.
45October 28, 2017The grill
46October 28, 2017Chassis matt black
47October 28, 2017Engine & parts painted. i wanted a casted look for the ochre part. Went okayish.
48October 28, 2017Tires painted mig 'rubber and tires'
49October 28, 2017The interior of the cab. First ever attempt to do high/low lights
50October 29, 2017Choices. Which logo should I use?
51October 29, 2017Picked the top one. Cut out the shapes in the masking tape. Screwed up the lower left one. Is going to be tricky to get them right on the model.
52October 29, 2017Masked
53October 29, 2017Masked
54October 29, 2017Purplish metallic decepticon colour
55October 29, 2017The result! Quite satisfied with this. The masks for the mud flaps were too fragile.
56November 1, 2017Assembly is easy.
57November 1, 2017
58November 1, 2017
59November 1, 2017
60November 1, 2017Cab getting there.
61November 1, 2017Stacks n stuff
62November 1, 2017Stacks mounted
63November 1, 2017Horns and lights
64November 1, 2017Blunt force trauma
65November 1, 2017Danger in the rear view mirror
66November 1, 2017
67November 1, 2017
68November 1, 2017
69November 1, 2017
70November 1, 2017
71November 1, 2017
コメント
2 May 2025, 23:26 -
Album info
This will be my Decepticon Motormaster. Ever since I saw this kit, I wanted to do this 🙂
